Skip to content

StateDMI / Command / CheckWellRights

Overview

The CheckWellRights command (for StateCU and StateMod) checks well rights data for problems. The command should usually be used with a WriteCheckFile command at the end of a command file.

Command Editor

The following dialog is used to edit the command and illustrates the command syntax.

CheckWellRights

CheckWellRights Command Editor (see also the full-size image)

Command Syntax

The command syntax is as follows:

CheckWellRights(Parameter="Value",...)

Command Parameters

Parameter             Description Default          
ID
required		 The identifier for the location(s) to check. Use * to match a pattern. None – must be specified.
IfNotFound One of the following:
  • Fail – generate a failure message if the location identifier is not matched
  • Ignore – ignore (don’t generate a message) if the location identifier is not matched
  • Warn – generate a warning message if the location identifier is not matched
 Warn

Examples

See the automated tests.

The following example command file illustrates how well rights can be defined, sorted, checked, and written to a StateMod file:

# Well Rights File (*.wer)
#
StartLog(LogFile="Sp2008L_WER.log")
# _________________________________________________________
# Step 1 - Read all structures
#
ReadWellStationsFromNetwork(InputFile="..\Network\Sp2008L.net")
SortWellStations()
# _________________________________________________________
# Step 2 - define diversion and d&w aggregates and demand systems
SetWellAggregateFromList(ListFile="..\Sp2008L_SWAgg.csv",PartType=Ditch,IDCol=1,NameCol=2,PartIDsCol=3,PartsListedHow=InColumn,IfNotFound=Warn)
SetWellSystemFromList(ListFile="..\Sp2008L_DivSys_DDH.csv",PartType=Ditch,IDCol=1,NameCol=2,PartIDsCol=3,PartsListedHow=InRow,IfNotFound=Warn)
#
SetWellAggregateFromList(ListFile="Sp2008L_AugRchWell_Aggregates.csv",PartType=Well,IDCol=1,PartIDsCol=2,PartsListedHow=InRow)
# _________________________________________________________
# Step 3- Set Well aggregates (GW Only lands)
# rrb Same as provided by LRE as Sp_GWAgg_xxxx.csv except non WD 01 and 64 removed
SetWellSystemFromList(ListFile="..\Sp2008L_GWAgg_1956.csv",Year=1956,Div=1,PartType=Parcel,IDCol=1,PartIDsCol=2,PartsListedHow=InColumn)
SetWellSystemFromList(ListFile="..\Sp2008L_GWAgg_1976.csv",Year=1976,Div=1,PartType=Parcel,IDCol=1,PartIDsCol=2,PartsListedHow=InColumn)
SetWellSystemFromList(ListFile="..\Sp2008L_GWAgg_1987.csv",Year=1987,Div=1,PartType=Parcel,IDCol=1,PartIDsCol=2,PartsListedHow=InColumn)
SetWellSystemFromList(ListFile="..\Sp2008L_GWAgg_2001.csv",Year=2001,Div=1,PartType=Parcel,IDCol=1,PartIDsCol=2,PartsListedHow=InColumn)
SetWellSystemFromList(ListFile="..\Sp2008L_GWAgg_2005.csv",Year=2005,Div=1,PartType=Parcel,IDCol=1,PartIDsCol=2,PartsListedHow=InColumn)
# _________________________________________________________
# Step 4 - Read Augmentation and Recharge Well Aggregate Parts
SetWellAggregateFromList(ListFile="Sp2008L_AugRchWell_Aggregates.csv",PartType=Well,IDCol=1,PartIDsCol=2,PartsListedHow=InRow,PartIDsColMax=25,IfNotFound=Ignore)
SetWellAggregateFromList(ListFile="Sp2008L_AlternatePoint_Aggregates.csv",PartType=Well,IDCol=1,PartIDsCol=2,PartsListedHow=InRow,PartIDsColMax=1,IfNotFound=Ignore)
# _________________________________________________________
# Step 5 - Read rights from HydroBase
ReadWellRightsFromHydroBase(ID="*",IDFormat="HydroBaseID",Year="1956,1976,1987,2001,2005",Div="1",DefaultAppropriationDate="1950-01-01",DefineRightHow=RightIfAvailable,ReadWellRights=True,UseApex=True,OnOffDefault=AppropriationDate)
# _________________________________________________________
# Step 6 - Sort and Write
#  Write Data Comments="True" provides output used for subsequent cds & ipy acreage filling
#  Write Data Comments="False" provides merged file used for seting ipy max pumping
SortWellRights(Order=LocationIDAscending,Order2=IDAscending)
# _________________________________________________________
WriteWellRightsToStateMod(OutputFile="Sp2008L_NotMerged.wer",WriteDataComments=True)
MergeWellRights(OutputFile="..\StateMod\Historic\Sp2008L.wer")
SortWellRights(Order=LocationIDAscending,Order2=IDAscending)
# _________________________________________________________
WriteWellRightsToStateMod(OutputFile="Sp2008L.wer",WriteDataComments=False,WriteHow=OverwriteFile)
# Check the well rights
CheckWellRights(ID="*")
WriteCheckFile(OutputFile="Sp2008L.wer.check.html",Title="Well Rights Check File")

Troubleshooting

See Also