StateDMI / Command / CheckCULocations

• Overview
• Command Editor
• Command Syntax
• Examples
• Troubleshooting
• See Also

---

Overview

The CheckCULocations command (for StateCU) checks the CU Location data for problems. The command should usually be used with a WriteCheckFile command at the end of a command file.

Command Editor

The following dialog is used to edit the command and illustrates the command syntax.

CheckCULocations Command Editor (see also the full-size image)

Command Syntax

The command syntax is as follows:

CheckCULocations(Parameter="Value",...)

Command Parameters

Parameter	Description	Default
ID	The identifier for the location(s) to check. Use * to match a pattern.	None – must be specified.
IfNotFound	One of the following: Fail – generate a failure message if the location identifier is not matched Ignore – ignore (don’t generate a message) if the location identifier is not matched Warn – generate a warning message if the location identifier is not matched	Warn

Examples

See the automated tests.

The following example command file illustrates how CU locations can be defined, sorted, checked, and written to a StateCU file (this is an abbreviated command file):

# Sp2008L_STR.StateDMI
# South Platte Decision Support System
# Historic Consumptive Use Model
# Structure File (*.str)
#
#  Step 1 - Read Structure List File (WDID, Name)
#
#  Structure List includes Key Structures from Task 3, Aggregate GW, and Aggregate SW
ReadCULocationsFromList(ListFile="Sp2008L_StructList.csv",IDCol=1,NameCol=3)
#
#  Step 2 - Read structure information from HydroBase (Latitude, County, HUC)
FillCULocationsFromHydroBase(ID="*",CULocType=Structure,Region1Type=County,Region2Type=HUC)
#
#  Step 3 - Assign AWC values based on Task 57, generate using the CDSS Toolbox
#
# # Key Structure AWC Values
SetCULocationsFromList(ListFile="AWC_2001.csv",IDCol=1,AWCCol=2)
#
# # GW AGG Structure AWC Values
SetCULocationsFromList(ListFile="AWC_Agg_GW.csv",IDCol=1,AWCCol=2)
#
# # SW AGG Structure AWC Values
SetCULocationsFromList(ListFile="AWC_Agg_SW.csv",IDCol=1,AWCCol=2)
#
#  Step 4 - Assign Elevation
FillCULocationsFromList(ListFile="Key_Elev.csv",IDCol=1,ElevationCol=3)
#
# Step 5 - Set Demand Structure Information based on Demand Carrier
SetCULocation(ID="0100503_I",Latitude=40.38,Elevation=4533.00,Region1="WELD",Region2="10190003",AWC=0.1375,IfNotFound=Warn)
SetCULocation(I
#
SetCULocation(ID="6400526",AWC=0.1393,IfNotFound=Warn)
#
# Missing values assigned to Diversion Systems
SetCULocation(ID="0100503_D",Latitude=40.28567,Region1="MORGAN",IfNotFound=Warn)
# DivSys and Aggregate use weighted latitude from climate station assignments
# County and HUC information not assigned to DivSys or Aggregate Structures
#
# Step 6 - Read structure climate weights from list created from the CDSS Toolbox Climate Tool
SetCULocationClimateStationWeightsFromList(ListFile="Climate_2001.csv",IDCol=1,StationIDCol=2,TempWtCol=3,PrecWtCol=3)
SetCULocationClimateS
# Set Climate Stations above 6500
SetCULocationClimateStationWeightsFromList(ListFile="SP2008_DWHA_OroAdj.csv",IDCol=1,StationIDCol=2,TempWtCol=3,PrecWtCol=4,OrographicTempAdjCol=6,OrographicPrecAdjCol=5)
#
# Step 8 - Fill Key Climate Station
#
FillCULocationClimateStationWeights(ID="01*",IncludeOrographicTempAdj=False,IncludeOrographicPrecAdj=False,Weights="0945,1.0,1.0")
#
# Step 7 - Write Structure File
SortCULocations()
WriteCULocationsToStateCU(OutputFile="SP2008L.str")
# Check the results
CheckCULocations(ID="*")
WriteCheckFile(OutputFile="SP2008L.str.check.html")

Troubleshooting

See the main troubleshooting documentation

See Also

• WriteCheckFile command