Direct Flow Exchange Direct (ityopr=24)
The type 24 operating rule allows a direct flow diversion's water right (ciopso(1)) to be exchanged to another direct flow structure, reservoir or plan
(ciopde). The exchange can occur from the river or by a carrier. The amount diverted can be limited to the amount available (Diversion) or its CU (Depletion).
The following comments are provided to assist in using and interpreting this operating rule:
- This operating rule controls both the source and exchanged (destination) diversion or storage. Any shortages at the source location are shared with the destination based on ownership of each.
- The percent ownership can be supplied that limits the exchange of the source water right.
- The consumptive use of the supply data can be specified to limit the exchange. The efficiency of water use for the exchanged water is set in the plan (*.pln) file. It may be set to a fixed efficiency for all months, a constant value for each of 12 months or to the efficiency of the source water right structure.
- The source water right may be transferred to a diversion, reservoir or plan (
ciopde). When the destination is a plan, the user is typically trying to 1. Satisfy a T&C Plan obligation or 2. Temporarily store the water in an Accounting Plan.- If a portion or all of the source water right has been changed and the destination is a changed water rights plan, it is recommended the user not use this rule and instead implement Changed Water Rights plan operations (See Section 7.11 and Section 4.13.26.
- Because a direct flow exchange right may be used to serve both a direct flow right and as a direct flow exchange right, the administration number assigned to the operating rule is used in the analysis for both the direct flow and the direct flow exchange (i.e. it is not overridden by the source water rights administration number).
- Direct flow exchange may be controlled over a season by using the monthly on/off switch (
imonsw(im)). Note the monthly on/off switches only control the exchange operation (i.e. the source water right continues to operate independent of the monthly on/off switch). - Monthly and Annual exchange limits are required as input.
- The exchange amount is the minimum physical water available, remaining decree of the exchanging right (e.g. some of the decree may have been used for direct diversion purposes), the exchange potential between the destination and exchange locations, the monthly and annual exchange limits and the destination structure’s capacity.
- Carrier losses associated with intervening structures may be provided if variable
OprLossis > 0 or = -1 and the variabledumx= 1-10 or < -12. Note carrier losses are routed back to the system using the return flow parameters associated with the carrier structure. - Terms and Conditions (T&C Plans) may be calculated if the source 2 variable (
ciopso2) is set to a T&C plan. The variableiousou(4,1)is used to indicate how and when T&C demands are calculated.- If the user is implementing T&C on a changed water right, it is recommended the user implement Changed Water Rights plan operations (See Section 7.11 and Section 4.13.26) and associate the T&C plan when the water is released from the Changed Water Rights plan.
- When
ciopso2= Plan ID andiopsou(4,1)= -1 the destination must be an accounting plan and the T&C Obligation is calculated when water is released from that Accounting plan using a type 27 or 28 rule. - When
ciopso2= Plan ID andiopsou(4,1)= 1 a standard return pattern is used to calculate the T&C Obligation. A Standard Return Pattern calculates the T&C Obligation to be:- \(\text{T&C Obligation (standard)} = (\text{Data in the return flow file (*.urm)}) \times ((\text{Released Water}) \times (1.0 - \text{CU Factor}))\) where the CU Factor is provided in row 5. The first value in a standard return flow table corresponds to the month diverted, the second to the month after a diversion, etc. Data that associates a Plan ID with any number of Return Flow Location(s), Percent(s), and Return Table ID(s) is provided in the plan Return File (*.prf).
- When
ciopso2= Plan ID andiopsou(4,1)= 2 a fixed return pattern is used to calculate the T&C Obligation. A Fixed Return Pattern calculates the T&C Obligation to be:- \(\text{T&C Obligation (fixed)} = (\text{Data in the return flow file (*.urm)}) \times (\text{Released Water})\) The first value in a fixed return flow table corresponds to the first month in the simulation (e.g. January for a calendar year simulation), the second month to February (again for a calendar year simulation), etc. Data that associates a Plan ID with any number of Return Flow Location(s), Percent(s), and Return Table ID(s) is provided in the plan Return File (*.prf).
- When
ciopso2= Plan ID andiopsou(4,1)= 3 a mixed return pattern is used to calculate the T&C Obligation. Mixed Return Pattern contains both a Standard and Fixed component and calculates the T&C Obligation to be:- \(\text{T&C Obligation (standard)} = (\text{Data in the return flow file (*.urm)}) \times ((\text{Released Water}) \times (1.0-\text{CU Factor}))\) where the CU Factor is provided in row 5. The first value in a standard return flow table corresponds to the month diverted, the second to the month after a diversion, etc. Data that associates a Plan ID with any number of Return Flow Location(s), Percent(s), and Return Table ID(s) is provided in the plan Return File (*.prf).
- \(\text{T&C Obligation (fixed)} = (\text{Data in the return flow file (*.urm)}) \times (\text{Released Water})\) The first value in a fixed return flow table corresponds to the first month in the simulation (e.g. January for a calendar year simulation), the second month to February (again for a calendar year simulation), etc. Data that associates a Plan ID with any number of Return Flow Location(s), Percent(s), and Return Table ID(s) is provided in the plan Return File (*.prf).
- When
ciopso2= Plan ID andiopsou(4,1)= 4 a default return pattern is used to calculate the T&C Obligation. A Default Return Pattern has a standard component that uses historic return flow data associated with the source water right to calculate the T&C Obligation. - If the variable
ciopso2is set to a T&C Plan ID andiopsou(4,1)is greater than zero then CU Factors are expected to be provided in card 5. Note the CU Factors typically represent negotiated values to, but not necessarily the same as, the efficiency of the Transfer From Structure. Also these factors are only used wheniopsou(4,1)= 1 (Standard Return) or 3 (Mixed Return) even though they are required as input.
- Water diverted by a Type 24 operating rule are reported in the Stream Report (*.xdd) as follows:
- At the source, the water exchanged to the destination is reported as Carried, Exchanged or Bypassed.
- At the destination, the water diverted is reported as From River by Other.
| Row-data | Variable | Description |
|---|---|---|
| Control Data | ||
| 1 | Format (a12, a24, 12x, 4x, f12.5, f8.0, i8, 3(1x,a12,i8), i8, 1x,a12, 1x,a12, 1x,2f8.0, 2i8) | |
| 1-1 | cidvri | Operational right ID |
| 1-2 | nameo(1) | Operational right name |
| 1-3 | rtem(1) | Administration number |
| 1-4 | dumx | Monthly and Intervening Structure Switch |
| +n = Number of intervening structures (max = 10) | ||
| 12 = Monthly (12) on/off values | ||
| -n = Include -12 monthly on/off values minus n intervening structures. Note, when a negative value is provided, it should be -13 or less for 12 monthly values and one intervening structure | ||
| 1-5 | ioprsw(1) | Annual On/Off Switch |
| 0 = off | ||
| 1 = on | ||
| +n = Begin in year n | ||
| -n = Stop after year n | ||
| Destination Data | ||
| 1-6 | ciopde | Destination structure (Diversion ID, Reservoir ID or Accounting Plan ID) |
| Use Type 26 operating rule and Type 13 plan for changed water rights. | ||
| 1-7 | iopdes(2,1) | Destination account |
| For a diversion destination, enter 1 | ||
| For a plan destination, enter 1 | ||
| For a reservoir destination, enter the account | ||
| Source Data | ||
| 1-8 | ciopso(1) | Source water right ID |
| 1-9 | iopsou(2,1) | Percent of source water right to exchange |
| 1-10 | ciopso(2) | T&C Plan ID |
| Enter NA if none or if the destination is an accounting Plan and the terms and conditions associated with this transfer will be calculated when water is released | ||
| 1-11 | iopsou(4,1) | 0 if ciopso(2) = NA |
| 1 for a standard return pattern | ||
| 2 for a fixed annual return pattern | ||
| 3 for a mixed return pattern | ||
| 4 for a default (source) return pattern | ||
| -1 the terms and conditions associated with this transfer will be calculated when water is released | ||
| Type Data | ||
| 1-12 | ityopr(1) | 24 |
| Associated Plan Data | ||
| 1-13 | creuse | Reuse Plan ID (enter NA if none) |
| Diversion Type | ||
| 1-14 | cdivtyp | Diversion or Depletion |
| Conveyance Loss (%) | ||
| 1-15 | OprLoss | 0 = No Transit loss |
| -1 = Provide intervening structure with loss data in row 3. | ||
| Miscellaneous Limits | ||
| 1-16 | OprLimit | 0 |
| -1 Execute the first iteration only. Review results – option not fully tested. | ||
| Start Date | ||
| 1-17 | IoBeg | First year of operation |
| End Date | ||
| 1-18 | IoEnd | Last year of operation |
| Monthly Data | ||
| 2 | Free Format (Include only if the variable (dumx) = 12 or less than -12) |
|
| 2-1 | imonsw(1) | Monthly switch 0 = off, 1 = on |
| +n = Day first used that month | ||
| -n = Day last used that month | ||
| Note the first entry corresponds to the first month specified in the control file | ||
| Intervening Structure Data without loss | ||
| 3 | Format (36x, 10a12) (Include only if OprLoss = 0 and the variable (dumx) = 1-10 or < -12) |
|
| 3-1 | intern(1,1) | For +dumx, Enter dumx intervening structure ID's |
For -dumx, Enter abs(dumx)-12 intervening structure ID's |
||
| Intervening Structure Data with loss | ||
| 3 | Free Format (Include only if OprLoss > 0 or = -1 and the variable (dumx) = 1-10 or < -12. See Section 7.11.4 for the approach used to model an augmentation station (e.g. a structure that carries a diversion, typically with loss, then returns non-lost water to the river).) |
|
| 3b-1 | intern(1,1) | Intervening structure ID (e.g. a Diversion ID or Stream ID) |
| 3b-2 | OprLossC(l,1) | Carrier Loss for Structure ID % |
| 3b-3 | InternT(1,1) | Intervening Structure Type |
| Enter Carrier if it is a diversion structure located on the river | ||
| Enter Return if it is a return location on the River | ||
Repeat for +dumx values |
||
| Exchange Limits (Monthly and Annual) | ||
| 4 | Free Format | |
| 4-1 | OprMax(1,1-12) | Monthly exchange limit (af/mo) |
| 4-13 | OprMax(1,13) | Annual exchange limit (af/yr) |
| T&C CU Factors Data | ||
| 5 | Free Format (Include only if ciopso(2) is a T&C Plan and iopsou(4,1) is >0. Note the data is only used when iopsou(4,1) is a standard return pattern (1) or a mixed return pattern(3).) |
|
| 5-1 | OprEff(1) | Efficiency in month 1 |
| 5-2 | OprEff(2) | Efficiency in month 2 |
| 5-12 | OprEff(12) | Efficiency in month 12 |